კვამლის დეტექტორები

SensoIRIS S130 is аn addressable optical-smoke detector designed for installation in addressable fire alarm systems supporting TTE communication protocol. The detector is powered on from the panel and can be controlled via the communication protocol. The detector SensoIRIS S130 is compatible with firebase B124 Features: - Sensitivity adjustment from the panel - Thin and simple design - Led indication with 360° visibility - Built-in isolator - EN54-7 and EN54-17 certified

SensoIRIS M140 is an addressable combined (temperature and smoke) detector designed for early fire detection. The detector works with panels that support the TTE communication protocol. The detector is compatible with the fire base B124. Features: - Certified by EN54-5, EN54-7 and EN54-17 standard - sensitivity adjustment from the panel - Day/night mode - Thin and simple design - LED indicator with 360° visibility - Status indication

SensoIRIS T110 is an addressable temperature detector designed to detect fire situations at an early stage. The detector works with panels that support the TTE communication protocol. Detector SensoIRIS T110 is compatible with fire base B124 Features: - Certified by EN54-5 standard - Can work in both fixed temperature and temperature rise detection mode - Choose a class from the panel - A1R, A2S, BS - Thin and simple design - LED indicator with 360° visibility - Status indication

SensoIRIS B124 is a standard base for addressable detectors and sounders SensoIRIS Series. Features: - Low profile design - Reliable contact system - Possibility of locking the detector to the base - BOSEC certified

SensoIRIS GAS is an addressable gas, LPG and CH4 (methane) leak detector. The gas detector has an automatic diagnostic function, it constantly checks the status of the sensor and electronics. SensoIRIS GAS is equipped with a button with the following functions: - Short press activates "SILENCING" mode, green LED flashes, buzzer and panel activation are disabled for 5 minutes. - If pressed for longer than 5 seconds, the "TEST" mode is activated, in this case the green, red and yellow LEDs are activated. The panel and buzzer are also activated. After 6 seconds, the gas detector emits 2 short beeps and turns off the "TEST" mode.

SensoMAG MCP150 is a fire alarm button with a built-in isolator module. The button is intended for addressable fire systems operating on the TTE protocol. The alarm button is activated by a finger press and sends a signal to the control panel to trigger an alarm for further response. Features: - Certified by EN54-11, EN54-17 and LPCB standard - Surface mounting - Reloadable construction - LED indicator - Includes a tool to reset the button - it is possible to attach a protective cap to the button (need to purchase separately, code - 40202191) - IP40 protection - Built-in isolator module

SensoIRIS MCP150 IP67 is a waterproof addressable manual call point designed for outdoor installations and IP67 environments, with a built-in isolator module. The call point is equipped also with a protective transparent cover for avoiding fault or accidental activation. SensoIRIS MCP150 IP67 is powered on from the fire panel and can be controlled via the communication protocol. Features: - Built-in isolator module - Surface mounting - Type (according to EN54-11) – A - LED indication - Special test tool for resetting after alarm event - Protective plastic cover - IP67 according EN 60529

The addressable manual call point is designed for application in addressable fire alarm systems, which support TTE communication protocol. The call point has a built-in isolator module which when used allows continuous operation of the loop in case of a short circuit and without the need of using additional isolator modules. The call point is powered on from the fire panel and can be controlled via the communication protocol. Features: - Working element (2 parts) - Frangible element – non-resettable (a broken glass) - Operating element – resettable (a button) - Call point type (method of operation according to EN 54-11) – B - Built-in isolator module - EN54-11 and EN54-17 certified

SensoIRIS S130 IS is аn addressable optical-smoke detector with a built-in isolator designed for installation in addressable fire alarm systems supporting TTE communication protocol. The detector is powered on from the panel and can be controlled via the communication protocol. The detector SensoIRIS S130 IS is compatible with fire base B124. - Sensitivity level selectable from the control panel – High/Normal/Middle/Low - Low-profile design - Led indication with 360° visibility - Built-in isolator - EN54-7 and EN54-17 certified

The SensoIRIS M140 IS an addressable combined (temperature and smoke) detector with a built-in isolator that can be placed to detect fires at an early stage. The detector works with panels that support the TTE communication protocol. The detector is compatible with the firebase B124 Available in two colors: white and black Features: - Sensitivity adjustment from the panel - Day/night mode - Thin and simple design - LED indicator with 360° visibility - Status indication - Built-in isolator - EN54-5, EN54-7 and EN54-17 certified

SensoIRIS T110 IS is аn addressable heat detector with built-in isolator designed for installation in addressable fire alarm systems supporting TTE communication protocol. Features: - Can work as a fixed temperature or rate of rise detector - Class, selectable from the control panel – A1/R, A2/S, B/S - Low profile design - LED indication with 360° visibility - Built-in isolator - EN54-5 and EN54-17 certified

SensoIRIS S130 IS Black is аn addressable optical-smoke detector with a built-in isolator designed for installation in addressable fire alarm systems supporting TTE communication protocol. The detector is powered on from the panel and can be controlled via the communication protocol. The detector SensoIRIS S130 IS is compatible with fire base B124. Features: - Sensitivity level selectable from the control panel – High/Normal/Middle/Low - Low-profile design - Led indication with 360° visibility - Built-in isolator - EN54-7 and EN54-17 certified

SensoIRIS B124 Black is a standard base for addressable detectors and sounders SensoIRIS Series. Features: - Color Black - Low-profile design - Reliable contact system - Possibility of locking the detector to the base

SensoIRIS WSB IP65 is a waterproof protected deep base specially designed for outdoor installations of addressable sounders SensoIRIS series. The deep base is suitable for wall mounting in applications in aggressive environments requiring IP65 protection of the devices. SensoIRIS B124 standard base is mounted with screws. Features: - Certified by EN 60529 standard - Protection IP65 - Surface mounting - wire max. Cross section 3 mm - Compatible with SensoIRIS series directional sirens

Duct Detector housing is a special box that works in combination with standard smoke detectors. The design allows the air from the duct to pass through the device, while analyzing it for the presence of smoke particles. The DUCT detector includes 2 pipes sampling pipe and outlet pipe, as each of them is 27 cm long. The housing is compatible with SensoIRIS B124 and SensoMAG B24 bases for connecting SensoIRIS S130 and SensoMAG S30 respectively. Features: - Detects and limit the spread of smoke inside the building HVAC ducts - Compatible with SensoIRIS B124 and SensoMAG B24 bases - Easy to access box - Transparent lid for device status visibility - Sampling and outlet pipes included (27 cm) - Mounting gasket included

SensoMAG S30 is an optical-smoke detector with a digital processing algorithm. The detector is designed to detect smoke in the very early stage of the fire situation. SensoMAG S30 is suitable for installation in any conventional fire alarm system designed with a fire alarm panel with a fire alarm threshold between 10mA and 15mA. Features: - Certified by EN54-7 standard - Auto temperature compensation - Digital processing algorithm - Thin and simple design - LED indicator with 360° visibility - Status indication every 8 seconds

SensoMAG M40 is a combined (smoke and temperature) detector with a digital processing algorithm, class A1/R. An integrated automatic recovery algorithm significantly reduces false alarm cases. The SensoMAG M40 can be installed in any conventional fire system operating within the 10mA and 15mA alarm thresholds. Features: - Certified by EN54-5/7 standard - Automatic temperature compensation - Digital processing algorithm - Low, slim design - LED indicator with 360° visibility - Status indication every 8 seconds

SensoMAG R20 is a conventional temperature detector with a digital processing algorithm. The detector reacts both to a rapid rise in temperature and to temperatures above 58°C. The SensoMAG R20 can be used in any conventional fire alarm system with fire alarm thresholds of 10mA to 15mA. Features: - Reacts to a rapid rise in temperature and also to temperatures above 58°C - Digital processing algorithm - Thin and simple design - LED indicator with 360° visibility - Status indication every 8 seconds - Certified by EN54-5 standard

SensoMAG F10 is a fixed temperature detector with a digital processing algorithm. The detector is designed to detect temperatures above 60°C (class A2/S, according to EN54-5). SensoMAG F10 is suitable for environments, where sudden large temperature changes are considered as normal, rooms with a high concentration of vaporous, exhaust gases, dust, etc. For example kitchens, garages, boiler rooms, or other places where it is not convenient to install fire alarm optical smoke detectors. Features: - Detects temperatures over 60°C, class A2/S - Digital process algorithm - Low-profile design - LED indication with 360° visibility - Sensor status indication every 8 seconds - EN54 – 5 certified

SensoMAG B12L/U is an alarm base (12V) with relay output. The base has two operation modes: Latch and Unlatch. The base is designed for conventional detectors SensoMAG series: F10, F10B, R20, S30, and M40 for applications in security alarm systems. The base is with low profile design and a reliable contact system. It is possible to lock the detector to the base for extra security. Features: - 12V - Application in intruder alarm systems - Latched/Unlatched mode

SensoMAG B24 is a standard base for conventional detectors SensoMAG series: F10, F10B, R20, S30, and M40. The base is with low profile design and a reliable contact system. It is possible to lock the detector to the base for extra security. - Compatible with alarm panels alarm state current up to 15 mA

SensoMAG MCP50 is a manual call point designed to work in conventional fire alarm systems. The call point has a resettable fragile working element, that sends an alarm signal to the fire alarm panel when triggered by a push in the indicated spot. The LED indication informs the user of fire and test events. Features: - Surface mounting - Resettable flexible element - LED indication - Special tool for resetting after alarm event - It is possible to attach a protective cap to the button (need to purchase separately, code - 40202191) - EN54 – 11 certified - Rate of protection IP 40

The AW-BK901 is an infrared linear reflex beam smoke detector. The device operates on the reflection principle: the emitter and receiver are combined into a single housing, while signal return is ensured by a reflector (mirror) installed on the opposite side. The system is equipped with an automatic calibration function, which allows for easy configuration of the device. For reliable operation, the detector features an automatic signal recovery capability, which eliminates false alarms. Features: - Manufacture in compliance with EN54-12 - Hassle-free alignment, built with a digital guide display and a laser beam pointing - Four ranges wide monitoring from 8-100 meters via encoder - Three users programming sensitivity adjustment - Built-in microprocessor - The self-diagnosis function can monitor for internal faults - Fire and fault-interfacing relays

The Fireray One is a beam smoke detector. The Fireray One is equipped with the One Minute Auto-Alignment™ feature, which ensures automatic alignment after positioning the laser onto the reflector and activating the system. It is equipped with Building Movement Tracking™ technology, which ensures the automatic correction of deviations caused by building movement and maintains precise beam alignment. Features: - Integrated user interface - Alignment mode switch, alignment direction buttons, and duration switches for alarm response threshold - Alignment status indicator - 2 green LEDs and 1 yellow LED - Green LED flashes every 10 seconds during stability - The red LED flashes every 10 seconds during a fault - Yellow LED flashes every 10 seconds for contamination or every 5 seconds for contamination